Photoshop synthesis Beauty and the beast the king of illustrators

This tutorial a bit more complicated production process. The material used and the effect is very large. Authors gave an overview of the production steps. There is also the handling of many details and some special effects production needs its own slow to grasp.

Let us look at what the final results:

1, a new Photoshop document to build a , using a light gray background, and then pull the girls pictures taken out, put the appropriate position.

2, Now we will change the tone of girls with curves to achieve. Curve parameters: RGB: Output: 119/Input: 157; Red: Output: 121/Input: 153; Green: Output: 165/Input: 133; Blue: Output: 149/type: 99. Effects of the following figure:

3, results have been pretty good, but here we make the color of clothes, like hats The colors, the implementation of the use of the image> adjustment> Replace Color command, to replace the blue part of the purple.

4, now has a good effect, and we in order to achieve better results, now face increased some better lighting effects, so copy the girl layer, and then the implementation of the image> adjustment> Brightness and Contrast (brightness: 20, contrast: 0).
in the layer mask (if it has not yet created one), with the Gradient tool to make the upper part of maintaining a higher brightness.



5, the use of 41 Grunge Brushes Brushes, and then use and the girl in the picture on the left image of the same color to use brushes. Click the girl with the Eyedropper tool select a color, when I painted the new layer where mad about. Finally you should see the following results:

6, now make images look better, back to girls Layer go to the left side of the layer mask with the grunge brush to add some black, looks like the girl has been painted out a piece, I also took this opportunity to adjust a bit the edge of the legs and angle.



7, we will produce the following photos of the background to add light effects. In order to better our production background, let's begin to create a layer above the background layer, set up three lines, the effect is as follows.



8, Now we began to make a background, create a layer above the gray background, and then use the radial gradient tool, a diameter of girls around the spray to the background, and then set the layer fill to 75%.

9, Here we are to make the background more attractive, so we find a material, into the background light level above, and then go to color, pattern adjusted to soft mode, fill is set to 46%.

10, in order to make the point light dark some, our new one layer, then use the radial gradient tool to fill the black, and then adjust the layer fill to 80%.

11, create a new layer, then use the Polygonal Lasso tool, select the following area, then use a white linear gradient to achieve the following effect diagram drawing tool.



12, layer fill adjusted to 20%, the effect is as follows.

13, then we create a circle the size of 30pixels, as a pattern , as shown below.



14, setting a transparent background, and then create a layer and then the pattern to fill. In order to obtain better results, we add a mask layer, then use the gradient tool to create a background, the effect is as follows.

15, in girls to create a layer underneath and then use the brush, set the following, drawing a lot of white dots and black dot pattern.



16, and then run the Motion Blur filter, the angle is set to 45, the distribution of 600, and then set the layer mode light mode, the effect is as follows.

17, then we create a new layer, then apply some dark yellow colors and patterns, set the layer mode to Overlay , fill adjusted to 25%.

18, now we open a material, and then put the background above the other.

19, to color, then adjust the fill to 40%.



20, we are behind girls in white gradient layer add some light.

21, create another layer, and then select the box to create a separate line, we get better results, rotate 45 degrees, and then move to the girls, top left, the effect is as follows.



22, and then we open Tiger's picture material.

23 , the tiger pictures on girls in the lower right corner, and then adjust the overlay layer.



24, and then use some smoke brushes, in the girl's lower right corner we have described some of the smoke, and then adjusted to 50% of the fill layer, the effect is as follows.

25, then we adjusted to the green part of the background, and then set the layer mode to Soft Light, filling adjusted to 75%.



26, you can add some green.

27 , and then open a material.



28, to color, and then adjust the layer mode to exclude model, the effect is as follows.

29, and then create a layer, add some smoke effects .



30, and then enter the word SOUL REBEL, filled with layers of 61%, use the Grunge Brushes Brushes to add some effects.

31 , when the dark can be adjusted some, filled adjusted to 69%, looks like the following results.



32, Linear Burn layer model, the effect is as follows.

33, we set the following colors, adjust the layer mode to linear light, filled with 75%, the effect is as follows.



34, create a layer, use the gradient tool gradient, and then adjust the pattern for the soft, filled to 35%.

end Effect:


This articlesource:Design and Material (http://www.q60.org),copy Please keep this line.