Photoshop synthetic tied over the branches of the sexy beauty

Let us look at what the final results:

1,. open the background image, change image colors: Image - adjustments - color balance, increase the red and yellow after ( Figure), then select highlight and shadow adjustment out your favorite color plane.

2, copy the sky layer, repeat the color balance adjustment tool (image> adjustment> color balance), this to add some blue and dark blue, remember to add some color to high light and shadow. Figure:



3, choose soft edge brush tool to erase the top part of the sky on the left. When using the eraser, it is necessary curve smear, it will give the colors more subtle. Figure:



4, add the character images, the use of Mobanggongju, select the character layer, and then click the Quick Mask, the use of hard-edged pen Brush cutting out characters, and then dragged into the background image, the figure:

5, to the character layer color, choose image> adjustment> Levels, adjusting out the match with the background color, as shown:



6, select image> adjustment> hue saturation, reduce saturation to -24, copying figures layers, Choose lower rungs of layers, use the Color Balance tool (image> adjustment> color balance) to add some red or yellow hue, as shown:



7, and then select the upper character layers, use the soft edge brush, wiping the decorative figures on the left to reduce the blue, and the corresponding reduction in the layer of transparent map layers combined figure, after can once again use Levels, color balance and hue saturation adjustment layer figure has reached the best results, refer to Figure:

8, people adjust the background image layer of the light the light from the left, in order to match characters and backgrounds, we have character layers use the Dodge tool to: Select Dodge tool, range: the middle of tune; flow rate: 32% in the figures on the back and skirt smear, but the colors do not too deep, and then use the Dodge tool to figure out the characters edge finishing lines (especially character's hair and left arm) Figure:



9, now we have to give people add some decoration, it is not difficult, you only need some trees and root image on it. We use these pieces of the tree and the root map, using color balance tools for processing.



10, first of all to find a good-looking roots, and then use your common Cutout tools (such as Magnetic Lasso tool or the Quick Mask board), plucked out of the roots, and copied to the graph, without worrying about cutting out the picture quality, while we have processed.

11, as shown, The new Material and making plans to join the colors are different, we can adjust as the previous material, as adjusted figures: Image - Adjustment - Levels, and adjust the slider, the slider from sliding to the left middle of the image will become brighter, right is dimmed, here we need to tune the dark, so drag the slider to the right. Now, selecting the location of roots in the picture, click on the image - adjustments - color balance, if the roots of the left arm on the characters, you need to adjust the red and yellow; but if placed on the right arm, will have to adjust the blue and blue. The first raising the yellow and red. Then we look at the effect of adjustment:



12, roots do a good job, the place you want to side position, and then rubber wipe tool modification and adjust the size, shown in Figure:



13, the last step, with better tools to create a shadow root: Figure, in the People depend on where the bottom of the left arm and roots, with better tools for painting, and select the color balance a little bit blue, can be filled to create an illusion of the roots.



14, the production of other roots are so the key is the interception of roots, the roots get a good, picture effects like.

15, finally explain, sometimes to achieve better visual effects, characters and figures can give a skirt attached to some of the roots to add a shadow, the following diagram:



16, only one difference in the character's right arm that location. Shadow produced at this location need to use layer styles. Double-click the root layer, open the Style menu (or choose Layer - Layer Style - projection), select and adjust the projection angle and opacity, as shown:



17, now let's add on the ground. The first picture is a simple sand floor, picture taken from inside a beach photo images.

18, lawn pictures taken from other sources. First of all, create a new grass layer, put it underneath the figure, the different parts of cut grass, and then mixed to produce images of grass. Shown in the figure:



19, create a new layer, the picture will be placed on the grass and ground layers in the figures between the high and low non - 1, a number of characters covers the feet, see below:



20, finally, at the edge of the place, add some grass and stones to cover the rough edges to make the production more perfect. See below:

21, now Let's add some close-ups of the roots and flowers. If you have read all the previous steps, then the rest is easier. As previously mentioned, the election map is very important, requiring a high-definition images, if the picture resolution is low, then the results will be produced very poor plan.

bear in mind this point, pick out the flowers, roots and trunk of the pictures, as mentioned above, carefully cut, and then copy the to the production of the figure, done with the previous method of mediation hue (image - adjustments - color balance).



22, flowers, roots and tree trunks do a good job, the production of map location of the ground. Methods, such as the first step above, the use of projection layer style (layer - layer style - projection. Select the ground layer, with better tools out of the shadow of James, the character's feet, now we produce some stains. Select a cloud picture, with the lasso tool to cut out of a cloud.



23, copy the clouds, and then click on the image - adjustments - Levels, select the middle, Move the slider to the right, so that clouds the color deepened.



24, and then decorated with soft corner eraser rubbing the edge of the clouds. Finally, select filter Mirror - blur - Motion blur, the direction from left to right 7 or 8 pixels, color pictures on this cloud layer below the figures; in copying a cloud layer, the top layer into the characters, open the image gamut to the middle slip block shift to the left, adjusting bright clouds, and then add the red and yellow color balance, making the final touches (image - adjustments - color balance)

25, the last part of the roots to add the final roots, we found the task of adding a sub-type roots. in the next diagram , we will merge some of the roots have reached the production of results.



26, the steps as before, cutting a good photo, first with Levels (image - adjustments - Levels), and color balance (image - adjustments - color balance) be fine roots, and then soft eraser erase the unwanted part of the angle, and the location of the edge of the roots to produce color Dodge effect, these are different parts of the roots of the effect of map:



27, looks pretty good bar. just need to carefully chosen root image the production method is the same. In order to create a more vivid is the picture, we need to add some squid, leaf valve and birds. I chose to take some of the more easy to pull the pictures, has reached a multiplier effect.

28, to complete the picture for a better production, we also need some modulation of work, select the upper layer, and then select the layer - New Adjustment Layer - Hue saturation, reduce saturation to around 10, or the extent of your favorite, and then try the other layers adjustment formula has reached the best results.



final result.


This chaptersource:Design and Material (http://www.q60.org),In this paper.